Radiographic Inspection

 Radiographic InspectionRadiography (X-ray) is one of the most important, versatile and widely accepted of all the nondestructive examination methods - Fig. 1. X-ray is used to determine internal soundness of the welds. The term "X-ray quality," widely used to indicate high quality in welds, arises from this inspection method.
Radiography is based on the ability of X-rays and gamma rays to pass through metal and other materials opaque to ordinary light, and produce photographic records of the transmitted radiant energy. All materials will absorb known amounts of this radiant energy and, therefore, X-rays and gamma rays can be used to show discontinuities and inclusions within the opaque material. The permanent film record of the internal conditions will show the basic information by which weld soundness and be determined.
X-rays are produced by high-voltage generators. As the high voltage applied to an X-ray tube is increased, the wavelength of the emitted X-ray becomes shorter , providing more penetrating power. Gamma rays are produced by the atomic disintegration of radioisotopes. The radioactive isotopes most widely used in industrial radiography are Cobalt 60 and Iridium 192. Gamma rays emitted from these isotopes are similar to X-rays, except their wavelengths are usually shorter. This allows them to penetrate to greater depths than X-rays of the same power, however, exposure times are considerably longer due to the longer intensity.
When X-rays or gamma rays are directed at a section of weldment , not all of the radiation passes are through the metal. Different materials, depending on their density, thickness and atomic number, will absorb different wavelengths of radiant energy.
The degree to which the different materials absorb these rays determines the intensity of the rays penetrating through the material. When variations of these rays are recorded, a means of seeing inside the material is available. The image on a developed photo-sensitized film is known as a radiograph. Thicker areas of the specimen or higher density material (tungsten inclusion), will absorb more radiation and their corresponding areas on the radiograph will be lighter - Fig 2.
Whether in the shop or in the field, the reliability and interpretive value of radiographic images are a function of their sharpness and contrast. The ability of an observer to detect a flaw depends on the sharpness of its image and its contrast with the background. To be sure that a radiographic exposure produces acceptable results, a gauge known as an Image Quality Indicator (IQI) is placed on the part so that its image will be produced on the radiograph.
IQI's used to determine radiographic quality are also called penetrameters. A standard hole-type penetrameter is a rectangular piece of metal with three drilled holes of set diameters. The thickness of the piece of metal is a percentage of the thickness of the specimen being radiographed. The diameter of each hole is different and is a given multiple of the penetrameter thickness. Wire-type penetrameters are also widely used, especially outside the United States. They consist of several pieces of wire, each of a different diameter. Sensitivity is determined by the smallest diameter of wire that can be clearly seen on the radiograph.
A penetrameter is not an indicator or gauge to measure the size of a discontinuity or the minimum detectable flaw size. It is an indicator of the quality of the radiographic technique.
Radiographic images are not always easy to interpret. Film handling marks and streaks, fog and spots caused by developing errors may make it difficult to identify defects. Such film artifacts may mask weld discontinuities.
Surface defects will show up on the film and must be recognized. Because the angle of exposure will also influence the radiograph, it is difficult or impossible to analyze fillet welds by this method. Because a radiograph compresses all the defects that occur throughout the thickness of the weld into one plane, it tends to give an exaggerated impression of scattered type defects such as porosity or inclusions.
An X-ray image of the interior of the weld may be viewed on a fluorescent screen, as well as on developed film. This makes it possible to inspect parts faster and at a lower cost, but the image definition is poorer. Computerization has made it possible to overcome many of the shortcomings of radiographic imaging by linking the fluorescent screen with a video camera. Instead of waiting for film to be developed, the images can be viewed in real time. This can improve quality and reduce costs on production applications such as pipe welding, where a problem can be identified and corrected quickly.
By digitizing the image and loading it into a computer, the image can be enhanced and analyzed to a degree never before possible. Multiple images can be superimposed. Pixel values can be adjusted to change shading and contrast, bringing out small flaws and discontinuities that would not show up on film. Colors can be assigned to the various shades of gray to further enhance the image and make flaws stand out better. The process of digitizing an image taken from the fluorescent screen - having that image computer enhanced and transferred to a viewing monitor - takes only a few seconds. However, because there is a time delay, we can no longer consider this "real time." It is called "radioscopy imagery."
Existing films can be digitized to achieve the same results and improve the analysis process. Another advantage is the ability to archive images on laser optical disks, which take up far less space than vaults of old films and are much easier to recall when needed.
Industrial radiography, then, is an inspection method using X-rays and gamma rays as a penetrating medium, and densitized film as a recording medium, to obtain a photographic record of internal quality. Generally, defects in welds consist either of a void in the weld metal itself or an inclusion that differs in density from the surrounding weld metal.
Radiographic equipment produces radiation that can be harmful to body tissue in excessive amounts, so all safety precautions should be followed closely. All instructions should be followed carefully to achieve satisfactory results. Only personnel who are trained in radiation safety and qualified as industrial radiographers should be permitted to do radiographic testing.